As above, just seen this whilst looking for a hose reel and appears to be a good price.
Was £34.99 allegedly and around £28 - £30 elsewhere.
Could be useful for others especially now the spring isn't too far away.
If this helps just one my job here is done :smile:
Description:
10m length, 7.5mm diameter hose.
Accessories included;
5 pattern spray gun.
1 hose end connector.
1 waterstop connector.
Threaded tap connector.
Reel can be free standing, .
Size H32.8, W26.7, D15cm.
Weight 1.77kg.
Manufacturer's 2 year guarantee .
EAN: 5010646055994.
Latest comments (21)
marktate
9 Feb 17#21
oos everywhere in the north east
Bigfootpete
9 Feb 17#20
Yay! I can finally wash my car!
**** - OOS anywhere close to me :disappointed:
andysfast
9 Feb 17#19
I bought one last year to use in my motorhom, it takes longer to fill the massive water tank but when on site but it's well worth it because of it's size and weight and it's good quality. For this price you can't not buy it.
BuckRodgers666
9 Feb 171#18
5.5l/min. Bosch 33-11. Tap easily outputting far greater than that, even with smaller diameter hose,
callum84
9 Feb 17#17
Higher water pressure can provide higher flow through smaller diameter.
Length of hose also affects flow as well as check valves and reduced bore valves.
It all depends what output flow your washer has. Some are as low as 5l/min and profesional 3ph or petrol units up to 20l/min.
May work ok on your washer but for someone else who has poor flow at tap or more powerfull unit It could cause serious damage which is not covered by warranty.
If you or anyone else is ever in doubt, fill a container from the end of hose you will be using and time how long it takes to fill. You can then work out lpm.
Compare this to max flow stated in manufacturers spec + 10% margin.
BuckRodgers666
8 Feb 17#16
Will look into it. Never gave it much thought really as it all sounds as though it's alright (naive there maybe) personally my water pressure is very high, so although the diameter is reduced, still confident it's getting enough water.
BuckRodgers666
8 Feb 17#8
It works with a pressure washer. Just non standard hose fit, so have to change the end. If you think it won't fit, it will, just have to soak it in boiling water to stretch it over the connector. I use it with Bosch unit
callum84 to BuckRodgers666
8 Feb 171#15
Yeah you can stretch it and make it fit, it might run but wont be doing your pump any good.
Pressure washers are positive fixed displacement pumps and displace the same amount of volume with each revolution.
The amount of water displaced is set by the pump pistons size and not water input.
If your feeding your pump less water than it is trying to use it creates voids of air at inlet. When these are then pressurised they violently burst causing damage to pump. In a piston pump it will also prematurely wear the flexible slipper joints on the pistons. Its called cavitation.
Manufacturers state a minimum hose and flow rate for exactly this reason.
My pressure washer outputs 9l/min. My 1/2" garden hose outputs 12l/min. If I restricted the diameter of hose it would without a doubt damage washer over time.
If you have low water pressure it makes problem even worse.
Look into it, I work with hydraulics daily and cavitation is one of the biggest causes of premature failure.
from what little I know karcher is a superior product
callum84 to saintscouple
8 Feb 171#14
They are both good hoses, just different sizes.
The one youv'e ordered is 1/2" ID. This is standard size for garden hose.
1/2 provides good flow and ideal for pressure washers, filling buckets etc. Takes the standard 1/2" hozelock etc fittings that you find everywhere.
One in this thread is nearly half the intenal diameter and will provide around half the flow and volume.
No good for pressure washers and takes longer to fill buckets etc.
Is however easier to store and more managable. Ideal for watering plants, small patios, balconies etc.
This is the tiny hose, I use one of these to send water to my cooper cooling ring when homebrewing...purchased last year in Wilko clearance these are good well made hose pipes thou expensive.
vivi_ssj3
8 Feb 17#1
is that the standard diameter hose or the tiny one?
![Fresh Breakfast Meat Box (Using code) @ Campbells Meat [Haggis / Lorne Sausage / Bacon / Black Pudding & More]](/images/topics/208684_1.jpg)
![[Xbox One] Q. u. b. e: Director's Cut on Deals with Gold](/images/topics/208716_1.jpg)
Opening post
Was £34.99 allegedly and around £28 - £30 elsewhere.
Could be useful for others especially now the spring isn't too far away.
If this helps just one my job here is done :smile:
Description:
10m length, 7.5mm diameter hose.
Accessories included;
5 pattern spray gun.
1 hose end connector.
1 waterstop connector.
Threaded tap connector.
Reel can be free standing, .
Size H32.8, W26.7, D15cm.
Weight 1.77kg.
Manufacturer's 2 year guarantee .
EAN: 5010646055994.
Latest comments (21)
**** - OOS anywhere close to me :disappointed:
Length of hose also affects flow as well as check valves and reduced bore valves.
It all depends what output flow your washer has. Some are as low as 5l/min and profesional 3ph or petrol units up to 20l/min.
May work ok on your washer but for someone else who has poor flow at tap or more powerfull unit It could cause serious damage which is not covered by warranty.
If you or anyone else is ever in doubt, fill a container from the end of hose you will be using and time how long it takes to fill. You can then work out lpm.
Compare this to max flow stated in manufacturers spec + 10% margin.
Pressure washers are positive fixed displacement pumps and displace the same amount of volume with each revolution.
The amount of water displaced is set by the pump pistons size and not water input.
If your feeding your pump less water than it is trying to use it creates voids of air at inlet. When these are then pressurised they violently burst causing damage to pump. In a piston pump it will also prematurely wear the flexible slipper joints on the pistons. Its called cavitation.
Manufacturers state a minimum hose and flow rate for exactly this reason.
My pressure washer outputs 9l/min. My 1/2" garden hose outputs 12l/min. If I restricted the diameter of hose it would without a doubt damage washer over time.
If you have low water pressure it makes problem even worse.
Look into it, I work with hydraulics daily and cavitation is one of the biggest causes of premature failure.
The one youv'e ordered is 1/2" ID. This is standard size for garden hose.
1/2 provides good flow and ideal for pressure washers, filling buckets etc. Takes the standard 1/2" hozelock etc fittings that you find everywhere.
One in this thread is nearly half the intenal diameter and will provide around half the flow and volume.
No good for pressure washers and takes longer to fill buckets etc.
Is however easier to store and more managable. Ideal for watering plants, small patios, balconies etc.
http://www.wickes.co.uk/Hozelock-Hose-Box-Set-30m+Spray-Gun/p/147143
This 7.5mm would restrict flow and depending how thirsty your unit is, wreck the pump.
:stuck_out_tongue: