Only available in 44 and 45. Two colour options, but cheaper than when last posted and deal went hot.
Their description:
Get off road with the very sturdy mountain bike shoe from dhb. The M1.0 features a Simple 3-strap closure and a rubber outsole with internal glass reinforced Nylon structure for excellent traction and great power delivery.
Top Features of the dhb M1.0 Mountain Bike Cycling Shoe
Glass reinforced Nylon polymer sole with rubber traction grip
Synthetic Upper
Quad core air mesh inserts
All-round ventilation holes
Internal thermo plastic heel counter
360 degree reflective detailing
2-hole cleat ready
Product Data
MTB: Yes
Cleat Fitting- 2 Bolt SPD Type: Yes
Forefoot Studs: Yes
Sole Material: Glass Reinforced Nylon, Rubber overmolded tread
Use: Off road
High Visibility: No
The design of the sole on this shoe has been engineered to strike a balance between the right level of stiffness for power transfer when on the bike, and ‘comfort’ when running or walking with the bike. The inner Glass reinforced Nylon core structure is topped with a high durability, high traction rubber compound with aggressive tread design to provide excellent grip on rocks, mud and road.
The sole is bonded to the synthetic upper which features the same quad core inner structure as the dhb road shoe. This mesh structure has excellent 3D mapping properties to achieve a form fit to the foot but provides almost zero stretch – which keeps input energy loss on the upstroke to an absolute minimum. The exterior upper is a durable Synthetic skin, which will absorb the knocks and grazes of general use. The reinforcement panel on the toe tip is double stitched for extra durability.
The simple 3-strap configuration allows the wearer to control the fitting across the full length of the shoe. By tightening the strap positions the wearer can achieve the correct balance between close fit (best power transfer) and comfort.
Mesh inserts across the upper on the instep and outer side of the upper allow air to circulate through the shoe helping to keep you temperature regulated as you generate heat.
At the ankle end of the shoe there is an internal thermo plastic heel counter, which is sandwiched between the cushioning layers of the shoe. This added support and stiffness allows the rider better control when engaging and disengaging from their clip-in pedal system.
Contrast red inner lining, and embossed printing provides a clean aesthetic, complimented with reflective detailing along the length of the shoe in-step and outside to enhance the rider’s safety in low-level light conditions.
The shoe is pre-drilled ready to use with MTB-style, 2-hole cleat-pedal systems (SPD, Crank Bros, Time MTB)
All comments (23)
jobibear
12 Mar 16#1
Plus tcb.
dpathic2001
12 Mar 16#2
Thanks, was looking for a basic entry level pair to go with my £8.69 Wellgo pedals deal :smiley:
backtothecaves to dpathic2001
12 Mar 161#4
Be prepared for a few accidents. I remember when I first got mine. Fell on my side in the middle of a busy high street.
Otto.uk
12 Mar 16#3
Thanks
Cheebley
12 Mar 16#5
Hence practice before you go out!!
rodman
12 Mar 16#6
black and white so ugly
black and red looking better
pnaylor39 to rodman
12 Mar 16#8
Sorry Disagree think black & red look more like a cheap looking pair of football boots@!
mattrixdesign2
12 Mar 16#7
Nice deal. Dhb kit is very good, but must admit I have not tried their shoes.
dpathic2001
12 Mar 16#9
Oh, I'm experienced in cleat catastrophes (Road bike though): 1st time was a bit comedy in front of a young lady driver. 2nd time was not so funny as I nearly fell in front of 40mph car traffic :confused:
SlurmsMacKenzie
12 Mar 16#10
Silly question but... are these suitable for use with all bikes or mainly just mountain bikes?
quakerphil to SlurmsMacKenzie
12 Mar 16#11
If you use pedals to match the cleats, you can use them on anything really. I use them on mtb and hybrid.
Opening post
Their description:
Get off road with the very sturdy mountain bike shoe from dhb. The M1.0 features a Simple 3-strap closure and a rubber outsole with internal glass reinforced Nylon structure for excellent traction and great power delivery.
Top Features of the dhb M1.0 Mountain Bike Cycling Shoe
Glass reinforced Nylon polymer sole with rubber traction grip
Synthetic Upper
Quad core air mesh inserts
All-round ventilation holes
Internal thermo plastic heel counter
360 degree reflective detailing
2-hole cleat ready
Product Data
MTB: Yes
Cleat Fitting- 2 Bolt SPD Type: Yes
Forefoot Studs: Yes
Sole Material: Glass Reinforced Nylon, Rubber overmolded tread
Use: Off road
High Visibility: No
The design of the sole on this shoe has been engineered to strike a balance between the right level of stiffness for power transfer when on the bike, and ‘comfort’ when running or walking with the bike. The inner Glass reinforced Nylon core structure is topped with a high durability, high traction rubber compound with aggressive tread design to provide excellent grip on rocks, mud and road.
The sole is bonded to the synthetic upper which features the same quad core inner structure as the dhb road shoe. This mesh structure has excellent 3D mapping properties to achieve a form fit to the foot but provides almost zero stretch – which keeps input energy loss on the upstroke to an absolute minimum. The exterior upper is a durable Synthetic skin, which will absorb the knocks and grazes of general use. The reinforcement panel on the toe tip is double stitched for extra durability.
The simple 3-strap configuration allows the wearer to control the fitting across the full length of the shoe. By tightening the strap positions the wearer can achieve the correct balance between close fit (best power transfer) and comfort.
Mesh inserts across the upper on the instep and outer side of the upper allow air to circulate through the shoe helping to keep you temperature regulated as you generate heat.
At the ankle end of the shoe there is an internal thermo plastic heel counter, which is sandwiched between the cushioning layers of the shoe. This added support and stiffness allows the rider better control when engaging and disengaging from their clip-in pedal system.
Contrast red inner lining, and embossed printing provides a clean aesthetic, complimented with reflective detailing along the length of the shoe in-step and outside to enhance the rider’s safety in low-level light conditions.
The shoe is pre-drilled ready to use with MTB-style, 2-hole cleat-pedal systems (SPD, Crank Bros, Time MTB)
All comments (23)
black and red looking better